First, note the number of the disk in the disk management window. For example, in the screenshot below, the Mac-formatted drive is Disk 2. Next, open a Command Prompt window as administrator. To do this on Windows 8 or Windows 7, press the Windows key once, type cmd, and press Ctrl+Shift+Enter. Sep 4, 2016 - How do I format an NTFS hard drive to mac format on a windows machine? SSD how to re format from mac osx journaled to be able to use in windows. Solved How can I install Mac OS X 10.9 onto an external HDD and run on a windows machine?
This answer explains how to format a WD drive for use on Windows and macOS.END External hard drives and external solid state drives come pre-formatted and ready for use. Internal HDD and internal SSD drives do not ship pre-formatted and will need to be Partitioned and formatted before being used.
Please note the instructions do not differ when formatting different capacity sizes, this is not capacity specific. Critical: The instructions in the article below are designed to help repartition and format a hard drive. This process is Data Destructive and cannot be undone.
Once the process begins, ALL THE DATA ON THE DRIVE WILL BE LOST! Important: Please note if this is the first time connecting an external device to a macOS, there is a Reformatting Required for Mac OS Compatibility, please see. Select an Operating System (OS) Operating System Instructions Windows 10 and 8.1 Windows 7 and Windows Vista macOS 10.14.x (Mojave) macOS 10.13.x (High Sierra) macOS 10.11.x (El Capitan) and macOS 10.12.x (Sierra) macOS 10.9.x (Mavericks), and macOS 10.10.x (Yosemite) macOS 10.7.x (Lion), and macOS 10.8.x (Mountain Lion) Both Windows and macOS (exFAT & FAT32). APFS formatted volumes can be read by a macOS High Sierra (10.13), but not by a macOS Sierra (10.12) or earlier. For more information, please refer to. If the following message occurs during the format procedure, MediaKit reports not enough space on device for requested operation.
Operation failed., please refer to. For instructions to convert a drive to (APFS) Apple File System Format on macOS High Sierra (10.13), please refer to Important: If at any time an error occurs stating that the drive can not be dismounted or unmounted, this is not caused by an issue with the hard drive. Please see for additional information on this particular issue.
How to Partition and Format a Drive on Windows 10 and 8.1 Partitioning a hard drive means preparing it to be used by the, creating a Volume for the OS to use. Formatting, however, deletes the content of a volume to clean it, and assigns a file system to it so that data can be moved into and out of the volume. Both processes are normally done together. Critical: The instructions in the article below are designed to help repartition and format a hard drive. This process is Data Destructive and cannot be undone.
Once the process begins, ALL THE DATA ON THE DRIVE WILL BE LOST! Windows 10 includes a built in utility known as Disk Management that can be used to partition and format a hard drive. To partition and format the drive with Disk Management, follow these steps:.
Right-click on Start, the Windows logo on the bottom-left of the screen, and click Disk Management. In the Disk Management window, the lower pane will display a list of available drives. Identify the drive that needs to be partitioned and formatted, and make sure that all critical data on this drive has been backed up elsewhere.
If there is already a partition on the drive, the bar above that drive will appear blue. If there is no critical data on the drive, or the data has been successfully backed up, right-click the bar and click Delete Volume. Important: If Disk Management shows the drive as Not Initialized, the drive will have to be initialized. For assistance initializing a hard drive, please see. If there is no partition and data on the drive, it will appear as Unallocated, with a black bar on top. Right-click the Unallocated space or the black bar, and click New Simple Volume.
The Welcome to the New Simple Volume Wizard will open. Click Next to proceed. Choose the volume size and click Next.
By default, the maximum disk space is already selected and it is recommended to leave it at the maximum disk space. Note: To create multiple partitions, select or type a specific number of megabytes (MB) for the first partition and continue to the next step. Once done with this process, the remaining space will display as unallocated space.
Now, create another New Simple Volume in the remaining unallocated space for the next partition. For example, on a 2TB drive, set the volume size to 1000000 (1 TB) and continue to the next step. When done, begin the New Simple Volume process again and select the remaining capacity, the unallocated space, for another 1TB partition. Assign a drive letter to represent the volume being created, and click Next. By default, this is the next available letter. Next is the File System, which controls how the data is read and written. Set the file system to NTFS, which is the default Windows file system, and leave the Allocation unit size to Default.
The Volume Label field can be customized in order to give the volume a desired name, such as My Book or WD Black 1. Check the box labeled Perform a quick format and click Next. Click Finish to begin formatting the drive. When complete, the drive will appear with a blue bar as in the image below.
How to Partition and Format a Drive on Windows 8 or 8.1 Partitioning a hard drive means preparing it to be used by the, creating a Volume for the OS to use. Formatting, however, deletes the content of a volume to clean it, and assigns a file system to it so that data can be moved into and out of the volume. Both processes are normally done together. Critical: The instructions in the article below are designed to help repartition and format a hard drive. This process is Data Destructive and cannot be undone.
Once the process begins, ALL THE DATA ON THE DRIVE WILL BE LOST! Windows 8 includes a built in utility known as Disk Management that can be used to partition and format a hard drive. To partition and format the drive with Disk Management, follow these steps:.
Right-click on the lower-left corner of the desktop screen and click Disk Management. In the Disk Management window, the lower pane will display a list of available drives. Identify the drive that needs to be partitioned and formatted, and make sure that all critical data on this drive has been backed up elsewhere. If there is already a partition on the drive, the bar above that drive will appear blue, which indicates the drive is already formatted and may contain data. If there is no critical data on the drive, or the data has been successfully backed up, right-click the bar and click Delete Volume. Important: If Disk Management shows the drive as Not Initialized, the drive will have to be initialized. For assistance initializing a hard drive, please see.
If there is no partition and data on the drive, it will appear as Unallocated, with a black bar on top. Right-click the Unallocated space or the black bar, and click New Simple Volume. Click Next to proceed. Choose the volume size and click Next. By default, the maximum disk space is already selected and it is recommended to leave it at the maximum disk space. Note: To create multiple partitions, select or type a specific number of megabytes (MB) for the first partition and continue to the next step. Once done with this process, the remaining space will display as unallocated space.
Now, create another New Simple Volume in the remaining unallocated space for the next partition. For example, on a 2TB drive, set the volume size to 1000000 (1 TB) and continue to the next step. When done, begin the New Simple Volume process again and select the remaining capacity, the unallocated space, for another 1TB partition. Assign a drive letter to represent the volume being created, and click Next. By default, this is the next available letter. Next is the File System, which controls how the data is read and written. Set the file system to NTFS, which is the default Windows file system, and leave the Allocation unit size to Default.
The Volume Label field can be customized in order to give the volume a desired name, such as My Passport or WD Black 1. Check the box labeled Perform a quick format and click Next. Click Finish to begin formatting the drive.
When complete, the drive will appear with a blue bar as in the image below. How to Partition and Format a Drive on Windows 7 and Windows Vista Critical: The instructions in the article below are designed to help repartition and format a hard drive. This process is Data Destructive and cannot be undone.
Once the process begins, ALL THE DATA ON THE DRIVE WILL BE LOST! Windows includes a built in utility known as Disk Management that can be used to partition and format a hard drive. To partition and format the drive with Disk Management, follow these steps:.
Click on Start and right-click Computer. Click on Manage. A window called Computer Management will open, displaying two panes.
On the left-side pane, under Storage, click on Disk Management. This will load Disk Management on the right-side pane. Disk Management will proceed to display all the hard drives detected by Windows.
The window may need to be maximized in order to see all the drives listed. The lower pane will display a list of available drives. Identify the drive that needs to be partitioned and formatted. It typically has a black bar indicating unallocated space. Important: If Disk Management shows the drive as Not Initialized, the drive will have to be initialized. For assistance initializing a hard drive, please see. If there is already a partition on the drive, the bar above that drive will appear blue.
This indicates that the drive is already formatted and may contain data. Make sure that all critical data on this drive has been backed up elsewhere. When ready to proceed, right-click on the blue bar and choose Delete Volume. The bar should now be black. Right-click on the unallocated space or the black bar to see a menu of available options, and click on New Simple Volume. The Welcome to the New Simple Volume Wizard will appear.
Left-click on Next to proceed to the next screen. Choose the volume size and click Next. By default, the maximum disk space is already selected and it is recommended to leave it at the maximum disk space.
Note: To create multiple partitions, select or type a specific number of megabytes (MB) for the first partition and continue to the next step. Once done with this process, the remaining space will display as unallocated space. Now, create another New Simple Volume in the remaining unallocated space for the next partition.
For example, on a 2TB drive, set the volume size to 1000000 (1 TB) and continue to the next step. When done, begin the New Simple Volume process again and select the remaining capacity, the unallocated space, for another 1TB partition. Assign a drive letter to represent the volume being created, and click Next. By default, this is the next available letter. Next is the File System, which controls how to data is read and written.
Set the file system to NTFS, which is the default Windows file system, and set Allocation unit size to Default. The Volume Label field can be customized in order to give the volume a desired name, such as My Passport or WD Black 1. Check the box labeled Perform a quick format and click Next.
Click Finish to begin formatting the drive. Note: If an error message is received stating that Windows is unable to unmount the drive, this means that there is a program or service currently reading or writing data on the drive. Determine what program is accessing the drive and shut it down, and then try again. Please see for assistance with this error under Windows. The listing for the drive (Disk 3 in the picture below) will say Formatting as it formats the drive. This process may take a few seconds. When the drive is done (Disk 3 in the picture below), the bar will be blue and the drive will say Healthy.
How to Partition and Format a Drive on Windows Vista Partitioning a hard drive means preparing it to be used by the, creating a Volume for the Operating System to use. Formatting, however, deletes the content of a volume to clean it, and assigns a file system to it so that data can be moved into and out of the volume. Both processes are normally done together. Critical: The instructions in the article below are designed to help repartition and format a hard drive.
This process is Data Destructive and cannot be undone. Once the process begins, ALL THE DATA ON THE DRIVE WILL BE LOST! Windows Vista includes a built in utility known as Disk Management that can be used to partition and format a hard drive. Please see for more information. Please follow the steps outlined below:. The lower pane will display a list of available drives.
Identify the drive that needs to be partitioned and formatted. It typically has a black bar indicating unallocated space. Important: If Disk Management shows the drive as Not Initialized, the drive will have to be initialized.
For assistance initializing a hard drive, please see. If there is already a partition on the drive, the bar above that drive will appear blue. This indicates that the drive is already formatted and may contain data.
Make sure that all critical data on this drive has been backed up elsewhere. When ready to proceed, right-click on the blue bar and choose Delete Volume. The bar should now be black.
Now right-click on the unallocated space or the black bar to see a menu of available options, and click on New Simple Volume. The Welcome to the New Simple Volume Wizard will appear.
Left-click on Next to proceed to the next screen. Choose the volume size and click Next. By default, the maximum disk space is already selected and it is recommended to leave it at the maximum disk space. Note: To create multiple partitions, select or type a specific number of megabytes (MB) for the first partition and continue to the next step. Once done with this process, the remaining space will display as unallocated space. Now, create another New Simple Volume in the remaining unallocated space for the next partition.
For example, on a 2TB drive, set the volume size to 1000000 (1 TB) and continue to the next step. When done, begin the New Simple Volume process again and select the remaining capacity, the unallocated space, for another 1TB partition. Assign a drive letter to represent the volume being created, and click Next. By default, this is the next available letter. Next is the File System, which controls how to data is read and written. Set the file system to NTFS, which is the default Windows file system, and set Allocation unit size to Default. The Volume Label field can be customized in order to give the volume a desired name, such as My Passport or WD Black 1.
Check the box labeled Perform a quick format and click Next. Click Finish to begin formatting the drive. Note: If an error message is received stating that Windows is unable to unmount the drive, this means that there is a program or service currently reading or writing data on the drive. Determine what program is accessing the drive and shut it down, and then try again.
Please see for assistance with this error under Windows. The listing for the drive (Disk 1 in the picture below) will say Formatting as it formats the drive. This process may take a few seconds. When the drive is done (Disk 1 in the picture below), the bar will be blue and the drive will say Healthy. How to format a drive on macOS 10.14.x (mojave) Critical: The instructions in the article below are designed to help repartition and format a hard drive.
This process is Data Destructive and cannot be undone. Once the process begins, ALL THE DATA ON THE DRIVE WILL BE LOST!. Open Disk Utility. Please See. From the left Column chose the External drive (My Passport, My Book, etc.). Click the Erase Button.
Type the drive new Name (My Passport, My Book, etc.). Click the Format drop down.
Choose a new Format: Mac OS Extended (Journaled). Click Erase button. When finished, the drive will be formatted and repartitioned successfully. Click the Done button.
How to partition and format A DRIVE ON macOS 10.13.x (High Sierra) Critical: The instructions in the article below are designed to help repartition and format a hard drive. This process is Data Destructive and cannot be undone. Once the process begins, ALL THE DATA ON THE DRIVE WILL BE LOST!. Open Disk Utility.
Please See. In the top menu bar, go to View, and choose Show All Devices. Click the eject button next to the drive volume (My Passport, etc) The drive Volume will now be greyed out. Select the drive (WD My Passport Media, etc). Click the Erase button.
Choose a new Format: Mac OS Extended (Journaled) Choose Scheme: GUID Partition Map. Type the drive new Name. Click the Erase button. When finished, the drive will be formatted and repartitioned successfully. Click the Done button. Critical: The instructions in the article below are designed to help repartition and format a hard drive. This process is Data Destructive and cannot be undone.
Once the process begins, ALL THE DATA ON THE DRIVE WILL BE LOST! Steps for macOS 10.11.x (El Capitan) and macOS 10.12.x (Sierra). Open Disk Utility. Please See.
Click the Eject button next to the external hard drive volume (My Passport, etc). The drive will now be greyed out.
Click the Erase button. Choose a new Format: Mac OS Extended (Journaled) Choose Scheme: GUID Partition Map. Type the drive new Name. Click the Erase button. When finished, the drive will be formatted and repartitioned successfully.
Click the Done button. How to Format or Partition a Drive on Mac OSX 10.9.x (Mavericks) and 10.10.x (Yosemite) Partitioning a hard drive means preparing it to be used by the, creating a Volume for the OS to use. Formatting, however, deletes the content of a volume to clean it, and assigns a file system to it so that data can be moved into and out of the volume. Both processes are normally done together. Critical: The instructions in the article below are designed to help repartition and format a hard drive. This process is Data Destructive and cannot be undone.
Once the process begins, ALL THE DATA ON THE DRIVE WILL BE LOST! Mac OSX 10.9.x, and 10.10.x include a built in utility known as Disk Utility that can be used to partition and format a hard drive. To partition and format the drive with Disk Utility, follow these steps:. Double left-click on the Mac HD, the internal Mac hard drive visible on the top-right corner of the desktop screen. Choose Applications from the left-side panel. While in there, open Utilities, and lastly double-click on Disk Utility.
Disk Utility will now be open. In the left-side pane, choose the drive that is to be partitioned and formatted. Typically there are two listings for each drive unless more than one partition exists on a particular drive. Choose the drive listing that is farthest to the left for the drive that will be formatted. It is usually directly above the name of the drive. In the example below, the one to be selected would be 495.78 GB WD My Passport 0830 Media.
After selecting the appropriate drive, additional options will appear on the right-side pane. Click on Partition. In the Partition area, click on the drop-down box under Partition Layout and select 1 Partition.
Note: Partitioning a drive is only necessary if planning to use multiple partitions on the drive. It's recommended using a single partition in most cases, if the primary objective is to simply prepare the drive for use with the computer, no partitioning is required. No further action is required. Click on the drop-down next to Format and from the drop-down menu select Mac OS Extended (Journaled).
This is the format that the drive will be formatted to. In the Name area, a drive name can be given to the drive by just typing in the desired name or drive label.
Click the Options button and choose Apple Partition Map. Then, click on Ok. Lastly, click on Apply. Important: If the Mac computer being used is an Intel-based Mac, Apple recommends to use the GUID Partition Table instead. A confirmation box will appear, reminding users that partitioning and formatting the drive will erase all information that is on the drive. Make sure that all critical information on the drive is backed up elsewhere before continuing.
If not, copy the data to another location. When ready, click on Partition. The disk will be unmounted before being formatted. Note: If an error message is received stating that the drive is unable to be unmounted, this means that there is a program or service currently reading or writing data on the drive. Determine what program is accessing the drive and shut it down before trying to format the drive again. If the error message persists, restarting the computer may resolve the issue.
If additional assistance is required, please. The drive is now formatting and at the bottom of the Disk Utility panel a Status Bar displaying the name of the drive, the format that's being applied to it, as well as the given name. When finished, the bar will go away and the drive will now be listed on the desktop.
How to Format or Partition a Drive on Mac OSX 10.7.x (Lion) and 10.8.x (Mountain Lion) Partitioning a hard drive means preparing it to be used by the, creating a Volume for the OS to use. Formatting, however, deletes the content of a volume to clean it, and assigns a file system to it so that data can be moved into and out of the volume.
Both processes are normally done together. Critical: The instructions in the article below are designed to help repartition and format a hard drive. This process is Data Destructive and cannot be undone. Once the process begins, ALL THE DATA ON THE DRIVE WILL BE LOST! Mac OSX 10.7.x, and 10.8.x include a built in utility known as Disk Utility that can be used to partition and format a hard drive. To partition and format the drive with Disk Utility, follow these steps:. Double left-click on the Mac HD, the internal Mac drive.
Choose Applications, then Utilities, and double-click on Disk Utilities. Note: If the screen does not look like the one in the picture below, the folder view may be set to a different one. Click on the Columns button (it's highlighted in blue in the screenshot) in the upper left corner of the window to change to the same view used here. In the far left pane, choose the drive that is to be partitioned and formatted.
Typically there are two listings for each drive, unless that particular drive has more than one partition in it. Choose the drive listing that is farthest to the left for the drive that is to be formatted. It is usually directly above the name of the drive. Once the drive has been selected, click on the Partition tab. Under Volume Scheme click the drop-down box and select 1 partition. Now, click the Options button and choose Apple Partition Map, then click on Ok.
Important: If the Mac computer being used is an Intel-based Mac, Apple recommends to use the GUID Partition Table instead. Click on the drop-down next to the Format option and change the Format to Mac OS Extended (Journaled).
A name can also be given to the drive by typing it into the Name box. When done, click on Apply. A box will come up warning that formatting and partitioning the drive will erase all of the information that is on the drive. If the information on the drive is no longer needed, then click on Partition. If the data on the drive is still needed, it will need to be copied to another location before proceeding. The drive is now formatting, and a status bar will be displayed at the bottom of the Disk Utility window.
This status bar will say formatting the disk, and gives the name of the drive, the format it is applying, and the name that was specified for it. When it is done, this bar will go away and the drive should now be listed on the desktop. If additional assistance is required, or more information is needed, please. Do not use the answer rating below to report technical issues.
Tuesday, November 28th, 2017 Author: Recently, some customers have reported experiencing a situation where their new will not show up in Disk Utility in High Sierra. Although Disk Utility should always be tried first, a Mac’s Terminal can be used to format the drive in these cases. If the original drive was not upgraded to High Sierra, that should be done first so the internet recovery feature on the computer is updated to High Sierra. Again, these instructions are intended for new internal SSDs only, with computers that have already had their original drive upgraded to. 1) After the new SSD has been installed into the computer, boot to internet recovery by pressing Command-Option-R until a globe is seen.
If the computer is not connected to the internet via an ethernet connection it will prompt for a wifi network to be chosen. It may take up to 10-15 minutes to complete the boot sequence, depending on internet speed. 2) Once at the macOS Utilities menu, select Disk Utility.
3) In the menu bar at the top of the screen click on the View menu and select Show All Devices. This should allow the SSD to show up in the left column, if it does not show up quit Disk Utility and reopen it. A) If the SSD does show up you may want to select the drive and click on the Erase tab.
You can then name the drive and chose the desired format (APFS is the best choice) and partition scheme (GUID is the best choice). Once the format is complete the SSD is ready for the OS to be installed.
B) If the SSD is not showing up Terminal sould be used to format the drive, which is outlined in the remaining steps. 4) Quit Disk Utility, then from the menu bar open the Utilities menu and select Terminal. Please read the notes below before proceeding: Note: We strongly recommend that you disconnect any externally mounted drives at this point, to prevent accidentally destroying the data on those drives.
For drives that cannot be disconnected, please make sure you have current backups of those drives. When using terminal it is important to type all commands exactly as they appear in this guide. Making a typo could result in lost data and time. 5) In Terminal type the following command, then press the Return key: diskutil list 6) A long list of disks will appear; we need to find our target disk from this list. An internal drive should be the very first or second drive in the list (see image below). The majority of the list is going to be ignorable disk images. To find the internal SSD, look for the following: ‘(internal, physical)’ which is shown in the blue box below.
You can further confirm you have the proper drive by looking at the size (red box). You will need to note the identifier of that drive (green box) for the next step. 7) In Terminal type the following command using the identifier found in the previous step and hit the Return key. Diskutil eraseDisk JHFS+ MacOS /dev/ identifier The process normally takes a minute or two to complete. When the process is complete, you will see the following message: “Finished erase on identifier” where identifier was the number you previously identified.
The SSD has now been formatted as a Mac OS Extended (journaled) volume named ‘MacOS’. Continue using this guide to format the disk as an AFPS volume, however if a Mac OS Extended (journaled) volume is desired you may now stop. 8) From the previous step we need to note the identifier of the new volume (red outlined box). It’ll be mentioned in the “Formatting identifier as Mac OS Extended (Journaled) with name MacOS.” In Terminal type the following command and hit the Return key: diskutil apfs createContainer /dev/ identifier The process normally takes a minute or two to complete. You’ll see the following message when done: “Finished APFS operation on identifier MacOS” 9) From the previous step, note the identifier from the newly created APFS Container (shown in the red box below) and use it in place of ‘ identifier’ in the final Terminal command, shown below the screenshot. In Terminal type the following command and hit the Return key: diskutil apfs addVolume identifier APFS MacOS The process normally takes a minute or two to complete.
When the process is complete, you’ll see the following message: “Finished APFS operation on identifier.” The SSD is now formatted as and is ready to use. Find more tips for macOS and at the Rocket Yard!. Recent Posts. Macs last a long time.
Don't plunk down your hard earned money on a new Mac when an upgraded Mac can run faster than a new Mac. We have the best upgrades and support for Macs: The easiest and most cost effective way to get the most from your Mac. Open and create more at one time with less slowdowns.
SSDs are up the 91 times faster than a hard drive. Unleash the true potential of you Mac by upgrading to an OWC SSD. OWC Install Videos guide you step-by-step so you can experience the blazing performance difference an OWC SSD offers. Easily expand your storage with durable external drives from OWC. From bus-powered portables to massive capacity desktop models, our external drives are time-tested and industry trusted to provide you great reliable storage whatever your needs may be. Who says the optical drive is dead?
Optical storage offers a great way to archive data long term, and Blu-ray media offers a tremendous amount of storage in a single disc. Watch Blu-ray movies to experience near studio master image quality. Our award-winning U.S. Based customer service is at the ready to help you with any upgrade questions you may have. We're available online and on the phone 24/7. Say hello today and find out what your Mac can do.
Comments are closed.
|
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |